Most Recent Update:
1/24/12 1:43 PM |
Parts and Components for Sale |  |
Complete Motors to bits and pieces Items are posted free of charge for the convenience of our competitors. If you wish to advertise a racing item for sale (sorry, no businesses), email information toJennifer at sacracewayjennifer@comcast.net If you wish to include a photos, please limit to clear shots of the vehicle or components at no larger than 3"x5", saved at 72dpi with picture named as item. example: "bobsmithfrontchevy" |
||
Torque Converter |
|
THIS IS A FULLY REBUILT 9 INCH 3500 STALL SPEED TORQUE CONVERTER
|
 |
HONDA/ACURA Rims and tires SOLD |
|
Components For Sale |
|
 |
|
Blower Restraint For Sale |
|
 |
|
Engine and Parts for Sale |
||
| 358 Engine 354 4-bolt Block with 492 heads, freshened & ready to go. It has Eagle Rods, Chevy Steel Crank, Crower CAM, Roller Rockers, Stainless Steel Rev Valves, Big exhaust, Small intake, with double hump heads. Strong motor! We are now asking $5,000.00 or best offer |
492 Heads Dedenbear TSC-4A throttle stop or four stage timer, very good cond 75.00/obo. email sstwonova@yahoo.com |
Complete Roller Motor Complete Chevy 428 from pan to intake. All new gaskets, seals, filters, etc. Corillo Rods SPS bolts. 400 Bow Tie Block - 4.125 Bore with 13.1 compression Jet Crank 4" stroke - (light weight, approx. 44 lbs. lighter then stock!) J/E Pistons & HD Pins. Speed Pro Rings BHJ Balancer. Federal Mogul Coated Rods, Mains, & Cam Bearings. Complete Isky Roller Cam Assembly Harlan Sharp 7/16 Roller Rockers - Pedestal mounted w/ stud girdles Isky tool room valve springs Brodix Aluminum Heads with stainless valves - #9 Edlebrock Victor Jr. Manifold. High Volume Oil Pump - modified 8 qt. Milodon oil pan & pick up. Edelbrock High Performance water pump. Braided side water lines to water pump Motor Balanced Internally. STRONG MOTOR!!!!!!!! Now Asking $6,000. or best offer! |
| Email (209) 993-6665 | ||
Parts for Sale |
Big Block Chevy 871 Blower with Hilborn injector Hat, Intake Manifold all pulleys and harmonic balancer (internal balance) , Hilborn fuel pump with Hilborn timing cover all braided fuel lines, fuel pressure gauge and 3 gallon Moon tank with mounting brackets. A complete set up for big block chevy this is not junk just removed from running car. Transmission The converter is a TCI Street Fighter 10". It was sent back to TCI about 2 years ago for a rebuild and added anti balooning plates. About 20 passes on this converter. All parts of this trans are in premium condition, no junk here. The C6 is a very durable transmission and should have years worth use left in it. I used it very little in a faily low powered car. This trans is still in the car and running so I can run this trans for you on jack stands, and even take you for a short ride if you have cash in hand. Pat $850/ OBO I also have a billet 31 spline 1350 series slip yoke available for an additional $75 |
"HOT STREET/ STRIP", 427 S.B.C. MOTOR, FOR SALE OR TRADE |
|||
  |
Rex Hutchison built 427 small block chevy motor Iskenderian #8005A springs T&D 1.60 sportcomp shaft rockers Holley modified/prepped 750dp. carb. Dart 220 race series manifold MSD #85551 pro-billet distributor MSD 8.5mm super conductor wire set Milodon #31060 oil pan Melling HV oil pump/pick-up BHJ damper Hughes SFI-29.1 approved flexplate Stewart stage-3 water pump Powermaster XS torque mini-starter Hooker #2243 ceramic coated, super competition headers, with copper gaskets Build sheet, Dyno. pull charts, along with a rolling engine cradle are included $12,000 OBO., for a complete, turn key ready mill, with everything listed above $10,000 OBO., for a complete long block, including the Hughes flexplate and BHJ damper, ready for your HP parts I will also offer as part of the package a Hughes GM-35 converter, and a pair of Borla XR-1 stainless steel race mufflers, a $600 dollar value I will also consider trades for a 1990's class A, or class C motorhome If interested you can reach me at: 916-517-5668 and my name is Gary McCallson |
||
NOS System For Sale Sold |
||
|
||